What sets ALLCUT machines apart.

01 / 08Steel magnet

A steel magnet that holds harder.

A magnetic drill is only as good as its grip on the steel. ALLCUT magnets are made of steel, not cast iron, because steel carries a stronger magnetic field — and the face is CNC machined flat, so all of it touches the work.

On the cutXpert 31/100, two coils give a pull of 2100 kgf: about the weight of two small cars.

2100 kgf

Magnetic force

2

Coils in the magnet

240 × 125 × 60 mm

Magnet size, L × W × H

700–2100 kgf

Across our magnetic drills

02 / 08Low maintenance

Low maintenance: less to wear, less to fix.

A machine waiting for repair is not earning. The drill head runs on a rigid steel slide, so it moves with very little shake — and less shake means less wear and a longer life.

Twist drills and adaptors fit straight into the MT-3 taper of the spindle, with no extra chuck in between to wear loose.

• Rigid steel slide
• Direct MT-3 spindle
• Overload protection
• Operating manual online

03 / 08Drill, cut, ream, tap

Drill, cut, ream and tap with one machine.

Carry one machine to the job instead of several. The cutXpert 31/100 takes four kinds of tool:

Twist drilling

up to 31 mm

An ordinary drill bit, for smaller holes — up to 250 mm deep.

Annular cutting

up to 100 mm

The cutter cuts only a ring, and the middle comes out as one solid slug. The fast way to make big holes.

Reaming

up to 31 mm

Opens a drilled hole to an exact size with a smooth wall.

Tapping

up to M30

Cuts a thread inside the hole, so a 30 mm bolt screws straight in.

04 / 08Overload protection

Overload protection saves the motor.

A blunt cutter, too much force on the handles or a jammed tool makes the motor work far past its normal load — that is how motors burn out.

Overload protection guards the motor when the load climbs too high, so a mistake costs you a minute, not a motor. There is a fuse on the control panel as well.

16 of 17

ALLCUT magnetic drills with overload protection

Fuse

On the control panel

05 / 08Powerful motor

A powerful 2000 W motor with two gears.

Big cutters and taps need slow, strong turning; small drills need speed. The 2000 W motor drives a two-speed gearbox, and electronic speed control lets you set the speed anywhere from 60 to 430 rpm.

Across the ALLCUT range, magnetic drill motors run from 1050 W to 2500 W.

2000 W

Motor power

2-speed

Gearbox

60–430 rpm

Speed, no load

220 V

Single-phase power

06 / 08Built tough

Built tough for work in any sector.

Magnetic drills are made for jobs where the steel cannot come to the drill: steel structures, bridges and towers, ships, rail, heavy fabrication and plant maintenance.

The cutXpert 31/100 has a steel magnet, a rigid steel slide and a 30 kg body, built at our works in Bhavnagar. It runs on 220 V single-phase power, so it needs no three-phase supply on site.

30 kg

Weight

220 V

Single-phase power

1991

Making magnetic drills since

07 / 08Customer care

Customer care from the people who build it.

ALLCUT has made machines in Bhavnagar since 1950. Call or WhatsApp +91 7600 252525 and you talk to our own sales team, who will help you choose the machine and the tooling for your job.

The data sheet and operating manual for every magnetic drill are on the Downloads page, and the adaptors and tapping chucks that fit each machine are on the Accessories page.

1950

Founded in Bhavnagar

16 of 17

Magnetic drills with manual and data sheet online

8

Accessories listed for the cutXpert 31/100

08 / 08Easy to use

Easy to use, from the first hole.

Each control has one job. The magnet has its own switch, apart from the big green ON and red OFF buttons of the drill motor, and the speed control sits on top of the motor.

Three long handles feed the drill down through a 280 mm stroke. To tap, run the tap in forward, then switch to reverse to bring it out.

280 mm

Stroke

3

Feed handles

• Separate magnet switch
• Forward and reverse
• Fine feed: optional